銀燦科技量產工具(Innostor MPTool)v2.11.02.11

銀燦科技量產工具(Innostor MPTool)是一款專業的量產工具，允許設置開卡流程、產品信息、開卡設定檔等參數，支持量產測試，軟件完全免費，綠色免安裝，操作簡單，需要量產銀燦設備的朋友可以下載！

【基本簡介】

U盤量產即U盤批量生產的意思。在U盤出廠時候最後一道工序是量產。而現實中，水貨U盤，或者需要製作帶CD-ROM盤的U盤，方便u盤裝係統，也用到量產。

而量產需要識別U盤的主控方案。也就是芯片方案。一般使用ChipGenius軟件查看，並且對應的下載相關量產工具。當然提醒大家的是盡量買原廠正品U 盤。芯片在量產之前首先要確定的就是自己U盤的主控芯片，確定之後才能找到合適的量產工具。主控芯片的分類有：群聯、慧榮、聯陽、擎泰、鑫創、安國、芯 邦、聯想、邁科微、朗科、閃迪。這些是可以通過ChipGenius檢測出的。

【軟件功能】

1、銀燦科技量產工具可以幫助用戶快速編輯自己的U盤係統

2、可以對損壞的設備修複，可以重新配置存儲係統

3、軟件可以設置的內容很多，量產的內容都在軟件界麵直接調整

4、可以對密碼設置，可以對連接的設備調整

5、提供多種開卡方式設置，也可以執行二次開卡

6、支持自動開卡，支持多支開卡，無法識別的U盤也可以開卡

【軟件特色】

1、USB-FDD （軟盤模式）： 啟動後U盤的盤符是A，且容量隻有1.44MB，至於FDD早就已經退出曆史舞台了；

2、USB-ZIP（大軟盤模式）： 啟動後U盤的盤符是A；USB-ZIP大容量軟盤仿真模式，此模式在一些比較老的電腦上是唯一可選的模式，但對大部分新電腦來說兼容性不好，特別是大容量 U盤。FlashBoot製作的USB-ZIP啟動U盤即采用此模式。USB-ZIP+增強的USB-ZIP模式，在DOS啟動後顯示A:盤，有些顯示 C:盤(根據電腦的BIOS支持情況不同)，支持USB-ZIP/USB-HDD雙模式啟動，從而達到很高的兼容性。其缺點在於有些支持USB-HDD的 電腦會將此模式的U盤認為是USB-ZIP來啟動，從而導致4GB以上大容量U盤的兼容性有所降低。

3、USB-HDD （硬盤模式）： 啟動後U盤的盤符是C。（注意：這個模式在安裝係統時容易混淆U盤和硬盤的C分區）；USB-HDD硬盤仿真模式，此模式兼容性很高，但對於一些隻支持 USB-ZIP模式的電腦則無法啟動。HPUSBFW工具製作的U盤即采用此啟動模式。USB-HDD+增強的USB-HDD模式，DOS啟動後顯示C: 盤，兼容性高於USB-HDD模式。同樣對僅支持USB-ZIP的電腦無法啟動。

4、USB-CDROM（光盤模式）： 啟動後U盤的盤符是光驅盤符。USB-CDROM光盤仿真模式，DOS啟動後可以不占盤符，兼容性比較高，新老主板一般都可以。優點可以像光盤一樣使用 (如，進行Windows係統安裝)。缺點，我們將失去對這部分U盤空間的寫權利，剩餘空間會被識別成為一個獨立的U盤，可以為Removable盤，當 然也可以做成Fixed盤，進一步分區；

【注意事項】

錯誤代碼說明：

11:"Open Execute File error!";

12:"Can't support NAND Function!";

13:"Send Execute CMD fail!";

14:"Check busy after Send Execute CMD!";

15:"Can't support NFTL Function!";

16:"Device Setup already, please erase first!";

17:"Can't support LED Function!";

18:"Check busy after Execute step!";

19:"Send GetMap CMD fail!";

20:"Return Channel not match!";

21:"Return Bank not match!";

22:"Return SizeofIDCode not match!";

23:"Return Flash ID not match!";

24:"Check busy after TestGetMap Step!";

25:"TestConfig Send IODriving_CMD fail!";

26:"TestConfig Send SET_ECC_CMD fail!";

27:"TestConfig Send SET_ACTiming_CMD fail!";

28:"TestConfig Send ConfigDevice_CMD fail!";

29:"TestConfig Send ConfigDevice_CMD fail!";

30:"Check busy after Send ConfigDevice_CMD!";

31:"Check busy after Test Config Step!";

32:"TestScanINIDFT Send CMD fail!";

33:"Check busy after TestScanINIDFT Step!";

34:"TestReadPhysical Send CMD fail!";

35:"TestCopy Send Init_NFTL CMD fail!";

36:"Check busy after Initial NFTL!";

37:"TestCopy Write fail!";

38:"TestCopy Read fail!";

39:"TestCopy RW Compare fail!";

40:"Check busy after TestReadPhysical Step!";

41:"TestErase Send CMD fail!";

42:"Check busy after TestErase!";

43:"Open USB FW File error!";

44:"Open SATA FW File error!";

45:"Send Write FW/Info CMD fail!";

46:"Check busy after Send Write FW/Info CMD!";

47:"Send Read FW/Info CMD fail!";

48:"Check busy after RW Info and FW!";

49:"Verify Info fail!";

50:"Write Descriptor fail!";

51:"Can't support Partition Function!";

52:"The Supported System IDs is incomplete!";

53:"open Image file fail!";

54:"Set Partition Fail!";

55:"Send Write Partition CMD fail!";

56:"Write CD-ROM partition fail!";

57:"Send ReadCapacity CMD fail!";

58:"Send Init_NFTL CMD fail!";

59:"Send Write Partition CMD fail!";

60:"Check busy after Partition!";

61:"Check busy after Copy Test!";

62:"This Format type not support!";

63:"This Windows version not support!";

64:"Can't get Diskletter!";

65:"Write Label name fail!";

66:"TestFormat fail!";

67:"Check busy after Format!";

68:"TestExecute ReInitial-Erase fail!";

69:"Inquiry Fail!";

70:"Can't Initial device , now run FW!";

71:"Check busy after Re-Initial erase Fail!";

72:"TestExecute Stop NFTL fail!";

73:"Send LEDC CMD fail!";

74:"TestFormat verify BPB fail!";

75:"Lock Disk fail!";

76:"UnLock Disk fail!";

77:"Get lock handle fail!";

78:"Get Total Sectors fail!";

79:"Open PC FW File error!";

80:"TestReadPhysical bad block over default setting!";

81:"TestReadPhysical Info-Block is bad!";

82:"Execute File not found!";

83:"TestReadPhysical Total size not enough!";

84:"TestReadPhysical Get total block too much!";

85:"TestFormat Create MBR error!";

86:"TestFormat Verify MBR fail!";

87:"Read Capacity fail!";

88:"Enable Optitmize for Performance fail!";

89:"Relink drive fail!";

90:"Disk size small than Media Partition!";

91:"Disk size small than Force capacity!";

92:"Can't support TEPF Function!";

93:"Refresh device fail!";

94:"Send Terminate CMD fail!";

95:"Check Unit Ready Timeout!";

96:"Innostor unlock CMD fail!";

97:"Innostor lock CMD fail!";

98:"Get Serial number fail!";

99:"Can't find good block to write FW!";

100:"Can't find good block to write Info!";

101:"TestConfig CT value error!";

102:"Hidden size incorrect!";

103:"Preload File Fail!";

104:"Can not find default Stor-String!";

105:"Write Info-Table fail!";

106:"Get Parameter fail!";

107:"Get Flash vendor fail!";

108:"Get Driving setting fail!";

109:"Can not Get File system!";

110:"Check Innostor device fail!";

111:"Check Preload files fail!";

112:"Cluster size not match!";

113:"Serial number over setting!";

114:"Not support ISF!";

115:"Set Permissions fail!";

116:"Can not support this version OS!";

117:"Not support this controller!";

118:"Support ISF Only!";

119:"Bad Block too much!";

120:"Serial number length not match!";

121:"Set parameter fail!";

122: "Device size over range!";

300:"SORTING_INVALID_HANDLE!";

301:"SORTING_SUCCESS!";

302:"SORTING_EVENT_FUNCTION_FAIL!";

303:"SORTING_STATUS_FUNCTION_FAIL!";

304:"SORTING_SET_PARAMETER_FAIL!";

305:"SORTING_GET_PARAMETER_FAIL!";

306:"SORTING_SET_PATTERN_FAIL!";

307:"SORTING_SET_TABLE_FAIL!";

308:"SORTING_ERASE_FAIL!";

309:"SORTING_WRITE_FAIL!";

310:"SORTING_READ_COMPARE_FAIL!";

311:"SORTING_GET_RESULT_FAIL!";

312:"SORTING_NOT_TLC_FALSH!";

313:"SORTING_FLASH_POWER_ONOFF_FAIL!";

314:"SORTING_SET_FEATURE_FAIL!";

315:"SORTING_SET_BMT_FAIL!";

316:"SORTING_BAD_BLOCKS_TOO_MUCH!";

317:"SORTING_NOT_SUPPORT_MULTI_CHANNEL_MULTI_BANK!";

318:"SORTING_SORTING_DATA_LENGTH_MISMATCH!";

319:"SORTING_SORTING_SET_ALPHA_TABLE_FAIL!";

320:"SORTING_VERIFY_IDBT_FAIL!";

321:"SORTING_QUICK_PARAMETER_FAIL!";

322:"SORTING_SORTING_INVLIAD_SORTING_LEVEL!";